Knowledge Base

Barionet answers:

• How to trigger InformaCast notifications on the IP Former using a Barionet400
• How to trigger Syn-Apps notifications on the IP Former using a Barionet400
• Barionet temperature monitoring with Node-RED, InfluxDB and Grafana
• How to send emails notifications from Barionet 200-400-1000-1100
• How to start BCL Programming on the Barionet50/100 ?
• Are there any differences between Barionet50 and Barionet100 in BCL programming?
• Can I connect a RS422 slave to the Barionet50?
• RS485 Termination
• How to get the IP Address
• What is the typical Barionet Power Consumption ?
• How do I set an I/O register using SNMP ?
• How do I read an I/O register using SNMP ?
• How to customize Barix Firmwares?
• Can I get the device's current IP in my BCL program?
• BaViDi to Show an Emergency Display upon Closure of Barionet 400 Inputs
• Control Barionet Relays from Informacast
• Local Audio FIles UDP Trigger from Barionet to IPAC

Perhaps also interesting:

• What is the difference between a package number and a device number?
• On the fly IP Address change
• WLAN Broadcast/Multicast Troubleshooting
• How to use Bit-reservoir?
• What is the difference in using PCM MSB and PCM LSB?
• How do emergency messages work ?
• How much latency should I expect in an Instreamer/Exstreamer setup using BTRP ?
• What does BRTP stand for ?
• What does RTP stand for ?
• Which port/s do your devices commonly use ?
• I want to do a broadcast over different subnets, is that possible ?
• I want to set up a local network with more than 250 devices, what do i have to do ?
• Do the Barix products support IPv6 ?
• Do the Barix products support Multicast and IGMP ?
• What is AutoIP, IPzator, etc.and how do I use them?
• SonicIP Voice - can I change this and record my own ?
• What is SonicIP?
• The device already has a password either I don't remember or I don't know, how do I erase it ?
• What if the device is still unreachable after a serial rescue ?
• How do I get the "status page" of any device ?
• How do I set the device back to factory defaults ?
• How do I do a web update of a device ?
• How do i connect a Barix device to HSPDA, UMTS, CDMA, EVDO, wireless networks ?
• What if my routers don't have a fix IP address from the ISP (Internet service provider) ?
• How do the devices get their IP address
• Are there any known security vulnerabilities with Barix devices?
• SIP with Siemens Gigaset
• When was RTP Buffering - Frame Based Buffering introduced?
• Which features are supported by the PC software, ICgraph?
• What you need to know about the ICgraph
• What to do with the SIP client
• How to create music channels on your network
• How to get the software
• How does the Barix system work?
• What is Digital Rights Management?
• Does the new Streaming Client version support the automatic Remote Firmware?
• What is the best way to Stream RTP from PC to Barix Devices?
• What to do with VSC support in the Streaming Client?
• How does the stream switching in the Streaming Client work?
• Windows Media Streaming (MMS/WMA)
• How to configure multicast?
• Protocols used in Barix Products
• SonicIP Howto
• How to customize the default configuration settings of your Barix Audio product.
• What you need to know about the Configuration Update
• Which of the 4 methods to use for operating a FW Update
• How to mount the ESD protection springs?
• Which firmware should you use for which hardware?

×