Congratulation for buying the Barionet 400 for Singlewire's InformaCast. We hope you find a quick start with this product and if a question remains, write us at email@example.com.
- 1 Female Terminal block
- Sticker with LAN MAC Address
1. Powering up
Slide the device upwards onto the DIN rail. Push it up and towards the rail until it snaps onto the upper rail edge.
Connecting to power and initialization
Power over Ethernet (PoE)
Simply connect a PoE supplied network cable into the network port and the device is starting up.
Option: Power Supply
The Barionet 400 also offers the possibility to be powered with a standard DC supply voltage of 9V to 30V, 4W max. Please mind the polarity. When powered up, the Status LED of the CPUs will start blinking, indicating that the device is starting up. When the device is initialized, the Status LEDs turn solid.
BLUE CPU LED: Main CPU
RED CPU LED: IO CPU
Configuration of a static IP
The Barionet 400 is configured to be a DHCP Client by default.
- Plug an Ethernet cable from the Barionet 400 to an Ethernet network.
- Use a Network Scanning Program or the Barix Discovery Tool in order to determine the IP Address according to the given MAC Address.
- In your Webbrowser connect to the determined IP Address.
- The Root Password of the Device can be found on a sticker on the Backside of the Device.
- Use the "Ethernet" Section in order to configure the Ethernet Interface:
Reseting and Rebooting Optioins
Rebooting the Device by Hardware Button
The Reset/Reboot can also be performed by the RESET Button on the Device. Use a needle to perform Reset by pressing the Button.
Resetting the Network Configuration
If you have entered a wrong Network configuration (Ethernet IP etc.), the Network configuration can be reset using the Factory Defaults Button. Press the button for 3-5 Seconds and the Network Configuration is reset to factory defaults (Ethernet back on DHCP).
Resetting Ethernet to Factory Default
The Factory defaults can be set by the DEFAULTS Button on the Device. Use a needle to perform Factory Defaults by pressing the Button for at least 10s.
At this point, the device will reboot and apply default settings.
Please note that all data except the User Partition will be deleted. Barionet Application Package will be set back to Firmware Image default.
J1 - 1xUSB Host
|2||D – (Data -)|
|3||D + (Data +)|
T1 - Ethernet (RJ45)
|1||TX + (Transmit data)|
|2||TX - (Transmit data)|
|3||RX + (Receive data)|
|6||RX – (Receive data)|
J8 - Digital Inputs, Relais, Power
|1..4||Digital Input 1..4|
|7||Relay 1 common|
|8||Relay 1 normally open|
|9||Relay 2 common|
|10||Relay 2 normally open|
|11||Relay 3 common|
|12||Relay 3 normally open|
|13||Relay 4 common|
|14||Relay 4 normally open|
|15||Power In + 9..30VDC|
|16||Power In - (GND)|
BLUE CPU LED shows Main CPU Status:
- blinking: startup
- solid: Main CPU running
RED CPU LED shows IO CPU Status
- blinking: startup
- red solid: IO CPU running
Green Digital Input LEDs show Status of Digital Inputs
- solid: Digital Input activated
Yellow Relais LEDs show Status of Relais Outputs
- solid: Relais Output activated
To modify the Barionet in addition to the InformaCast settings, please read the Barionet 400 standard manual.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Safety and precaution recommendations apply. Find them in the download section at www.barix.com